Do-it-yourself pallet dog booth

Content

1 Where to start
2 What size to make a booth
3 We calculate the size of the manhole
4 Determining the shape of the roof
5 Methods and materials used to insulate the booth
6 Master class for making a booth from pallets

The optimal material for building a doghouse is wood. However, edged boards are expensive and not always available. Other materials at hand are not suitable for the kennel. How, then, to solve the problem with housing a pet dog? The way out of the situation will be wooden pallets. They are also called pallets. These are wooden boards of a certain size, on which products are moved in warehouses or a store. Pallets are discarded as they wear out. And they are just that very free handy material, suitable for the construction of a kennel. Now we will figure out how to quickly build a doghouse from pallets and insulate it.

Where to start

So, making a dog kennel with your own hands begins with the preparation of material. In our case, you need to get at least five pallets. Shields themselves, as a ready-made structure for the walls of the booth, will not work. The pallet consists of a bar, on which boards are stuffed on both sides with a small gap. To build a doghouse, pallets will need to be disassembled into building material. Only one shield is left untouched, which will go entirely to make the bottom of the kennel.

Important! Pallets were made to move different types of products, and their device may differ in the size of wooden blanks. If you come across shields with jumpers from a thick bar, you will need to saw it lengthwise to make the frame of the booth.

The parts of the disassembled pallets must be sorted immediately. The boards will be used to cover the dog kennel, and the frame of the house will be made from the timber.

What size to make a booth

There are rules for calculating the dimensions of a doghouse. The dog should feel free inside the kennel and be able to turn around. It is also impossible to make a booth that is too spacious. It will be cold in it in winter. You can determine the size of the house only by measuring the size of the dog.

The photo shows a diagram showing all the places where you want to take a measurement. The width and depth of the room is calculated from the length of the dog. The lying dog is measured from the edge of the extended front paws to the end of the tail, and a margin of 15 cm is added.However, in our case, the bottom is a finished pallet with fixed dimensions. There are only two exits to be found here:

If the dimensions of the dog greatly exceed the permissible dimensions, the pallet will have to be disassembled, and the bottom of the required dimensions will have to be folded from the blanks.
When the results of measurements of the dog showed small deviations from the required size or the dog is much smaller, then the tray for the bottom of the kennel can be left in its original state.

In contrast to the dimensions of the bottom, the height of the booth can be freely adjusted. After all, the walls will be assembled by hand from disassembled pallets into blanks. You can determine the height of the kennel by the height of the dog, which is measured at the withers. For a headroom, add 10 cm to the result obtained.

We calculate the size of the manhole

The manhole in the booth is not cut out just like that. A few more measurements will be required here. The dog is the watchman. The dog must freely jump in and out of the kennel to fulfill its guard duties. The width of the hole is cut 5–8 cm more than the width of the dog's chest. 5 cm is added to the measurement at the withers, determining the height of the manhole.

Advice! If there is such an opportunity, the hole for the puppy is made of the required size, and as it grows, the entrance to the kennel is expanded.

The manhole on the booth can be cut into a rectangular or oval shape, but it is not placed in the center of the front wall. It is better to enter the entrance with an offset to one of the side walls, then a blind corner is obtained in the booth. Here the dog will be able to hide from the wind.

Winter kennel options provide for a partition inside the house with another manhole. The booth is obtained in two compartments: a sleeping room and a vestibule. The idea is, of course, good, but not suitable for all breeds of dogs. Conscientious guards rarely visit the bedroom due to the fact that they cannot control their territory from there. Such dogs constantly lie in the vestibule, looking out of the manhole, and the bedroom, in fact, remains unclaimed. Making a kennel from pallets with your own hands, it is still better to stop at a one-room house with an offset access hole.

Advice! It is necessary to cut a hole in the kennel so that a sill about 15 cm high is obtained from below. Behind it, a lying dog will be able to hide his nose from the frosty wind.

Determining the shape of the roof

The roof of the house can be made flat with one slope or a gable structure can be built. The second option is considered not very successful. The only plus can be only an increase in height due to a gable roof on a small booth. Building such a structure is much more difficult than a flat roof. With the onset of winter frosts, excess space will make itself felt. It will be very cold in the booth, and all the heat will rise to the ridge of the roof and go out into the street through the cracks.

A pitched flat roof is easy to manufacture. It can be cut even from a piece of OSB slab, and covered with any roofing material on top. Another advantage of the flat roof is that the dog can lie on it. Many dogs love to relax on the roof of the booth in the summer and watch their territory.

Advice! It is better to make a flat roof hinged or removable. Then the possibility of easy access to the kennel for cleaning is provided.

If, in terms of aesthetics, only a gable structure is acceptable, then it is advisable to nail a ceiling in the booth, separating the attic space from the living space.

Since we are talking about the roof, we need to dwell a little on the manufacture of a canopy. Many dogs love to stand outside even in the rain and snow. If there is extra building material and desire, a small canopy can be installed over the booth. Then the dog will be able to walk freely in any weather, and in the summer it will hide from the sun.

Methods and materials used to insulate the booth

You can insulate a dog kennel with your own hands with any heat-insulating material. Mineral wool is ideal. Styrofoam is also not bad, but the dense material forms the effect of a thermos inside the house. If in winter the manhole is closed with a curtain, it will be difficult for the dog to breathe due to the lack of fresh air. In this case, a gap is left or a ventilation hole is made.

All structural elements must be insulated at once: walls, bottom and ceiling. You should not use a lot of insulation. Nature arranged it so that dogs warm themselves well with their wool. A thick layer of insulation will create a sharp difference between the outside temperature and inside the house. For a dog, such a change in conditions is unacceptable.

Advice! In case of unexpectedly severe frosts, straw is placed inside the kennel. The dog will distribute himself how much bedding he needs, and throw the rest of the straw out of the booth.

Master class for making a booth from pallets

Now we will look at a step-by-step photo of how to make a dog house from old pallets. As you remember, we disassembled all the panels into blanks, only one pallet remained for the bottom. Here we begin the construction of the kennel with him:

Thanks to the pallet, we will have a booth on legs, and dampness and rainwater will not penetrate inside. We make the house insulated, so we put a sheet of foam plastic 20 mm thick on the pallet, and on top we fasten the OSB plate with screws.
At the corners and in the center of the long sides of the pallet, we nail racks from a bar with a section of 50x50 or 40x40 cm.
We knock down the frame strapping from the same bar from above.A roof will be attached to this frame in the future.
We sheathe the frame of the booth with boards from the inside. For work, the pallets were taken old, so there can be a lot of chipped chips on them. So that the dog does not get hurt, we grind all the boards well with sandpaper.
After attaching the inner lining to the outside of the box, cells were obtained. We put foam plastic with a thickness of 20 mm here.
On the front wall from a bar we assemble a manhole, after which we also insulate all cells with foam.
From the OSB slab with an electric jigsaw, we cut out four rectangles according to the sizes of the sides of the box, and from them we make the outer casing of the booth. On the front wall, where the hole should be, we cut out the window in the OSB with the same jigsaw.
For a roof from a bar we knock down a frame. We trim it with a board from the inside. We put polystyrene in the cells, and on top we fix the OSB plate. It must be cut to a larger size than the booth itself in order to get a visor.
In the final, you should get such a booth for a dog.